SpeedyBee F405 V3 BLS 50A BMI270 30x30 FC/ESC Stack 4IN1 ESC RC Model

Description: Item: SpeedyBee F405 V3 50A Flying Tower (F405 V3 Flight Control BLS 50A 4in1 ESC)Parameters:SpeedyBee F405 V3 Flight Controller MCU:STM32F405IMU (gyroscope):BMI270USB Port Type:Type CBarometer:InternalOSD Chip:AT7456E ChipBLE Bluetooth:Support, for parameter tuningDJI Air Unit Connection Method:Support 6pin socket direct connection, welding wire connection two waysMicroSD Card Slot Blackbox:Support, please use a MicroSD card of SDSC/SCHC type below 4GB, which must be formatted in FAT16/FAT32 format. Do not use SDXC type cards. Note: Betaflight only supports up to 4GBGalvanometer Input: Supported. When paired with SpeedyBee BLS 50A ESC, please set Scale=386, Offset=0Betaflight camera parameter adjustment pad: Support (front CC pad)Power input:3S - 6S Lipo (Through the 8pin interface on the back or the G, BAT pins/pads in the pads)5V BEC Output :9 groups of 5V output, (4 +5V pads on the front and 1 BZ+ buzzer pad, and one +5V pad on each of the 4 corners for external LED lights), the total current output is 2A9V BEC Output :2 groups of 9V output, (1 +9V pad on the front, +9V output in a seat on the back), the total current output is 2A3.3V BEC Output :1 group (1 3.3V pad on the front), the maximum current is 500mA4.5V BEC Output :2 groups (2 4.5V pads on the front), the maximum current is 1AESC signal: M1-M4 on the back and M5-M8 on the frontUART serial port: five groups of serial ports (UART1, UART2, UART3, UART4 , UART6)ESC telemetry input: R4 (UART4)I2C:Support. SDA, SCL pads on the front. For magnetometers, sonar, etc.Legacy Betaflight LED Pads: Supported. 5V, G, LED strip on the bottom of the front. For BF control WS2812 LED lightBuzzer:Support .BZ+ , BZ- pad used for 5V buzzerBOOT key:Supporte.Press and hold the BOOT key to power on, you can enter the DFU mode, which is used to save the brick and flash the firmware; in the power-on standby state, the BOOT key is also used to control the LED strips connected to the D1-D4 pads on the four corners of the PCB. By default, short press the BOOT key to cycle through the LED display status; Changan BOOT key switches the LED control mode: SpeedyBee LED or BF LED. In BF LED mode, these LED strips will be controlled by BF firmwareRSSI pad:Support. Labeled as RSSmartPort:Support. You can use any set of serial port TXSupported flight controller firmware:BetaFlight (default), EMUFlight, INAVFirmware target name:SPEEDYBEEF405V3Mount:30.5x30.5mm (4mm hole diameter)Dimensions:41.6(L) x 39.4(W) x 7.8(H) mmWeight:9.6gSpeedyBee BLS 50A 4-in-1 ESCFirmware:LHeli_S JH50Wireless configuration:Full configuration supported by SpeedyBee AppPC configurator download link:ttps://esc-configurator.com/Continuous Current:50A*4Break current:55A (5S)Protective Diode for TV:YesExternal Capacitor:1500uF Low ESR Capacitor (included in the package)Protocol ESC:DSHOT300/600Power Input:3-6S LiPoOutput power:VBATCurrent sensor:Support (scale=386 offset=0)Mount:30.5x30.5mm (4mm hole diameter)Dimensions:45.6(L)*44(W)*6.1mm(H)Weight:13.8g

Price: 39.99 USD

Location: shnzhen city

End Time: 2024-09-24T06:50:52.000Z

Shipping Cost: 10 USD